1.车间位置和消防设施?：车间位置不宜建在水边，以减少湿空气的影响。周围不要堆放易燃物，要留有消防车辆的通道，设置消防栓。车间内应常备灭火器、沙箱、灭火毯，车间附近应设有自来水空头?。

1. Workshop location and fire-fighting facilities? The workshop location should not be built near water to reduce the impact of humid air. Do not stack flammable materials around, leave a passage for fire trucks, and install fire hydrants. Fire extinguishers, sandboxes, and fire blankets should be kept on hand in the workshop, and there should be a water outlet near the workshop?.

2.温湿度控制?：温湿度应控制在适宜范围内，冬天温度应大于15度，夏天小于30度，非常好将温度控制在20-25度，湿度应保持在75%以下。如果没有条件调温、调湿，应做到机械通风，保持室内空气干净?。

2. Temperature and humidity control? The temperature and humidity should be controlled within an appropriate range, with temperatures exceeding 15 degrees Celsius in winter and below 30 degrees Celsius in summer. It is best to keep the temperature between 20-25 degrees Celsius and the humidity below 75%. If there are no conditions for temperature and humidity control, mechanical ventilation should be implemented to keep indoor air clean?.

3.通风要求?：排风量大约按5次/每小时的换气次数设计，排风口应设在下方，送风应在上方。如果送、排风同事进行的话，排风量应大于送风量。如果无条件进行机械空调，仅靠自然通风时，则车间要宽敞并设置气窗?。

3. Ventilation requirements? The exhaust air volume should be designed based on a ventilation rate of approximately 5 times per hour, with the exhaust outlet located below and the supply air located above. If the air supply and exhaust are carried out by colleagues, the exhaust volume should be greater than the air supply volume. If mechanical air conditioning is used unconditionally and only natural ventilation is used, the workshop should be spacious and equipped with ventilation windows?.

4.照明和防火?：车间照明应以自然采光为主，光照要均匀，避免太阳直射到操作面上。此外，桥架填料主要是氢氧化铝、阻燃剂和其他材料，当出现外部火灾和局部电缆火灾时，能够挥发出水蒸气，熄灭火源、阻止火焰蔓延、降低电缆环境温度?。

4. Lighting and fire prevention? Workshop lighting should mainly rely on natural lighting, with even illumination to avoid direct sunlight on the operating surface. In addition, the bridge filling is mainly made of aluminum hydroxide, flame retardants, and other materials. When there is an external fire or a local cable fire, it can release water vapor, extinguish the fire source, prevent the spread of flames, and reduce the temperature of the cable environment?.

5.设备设置?：为适应模具的吊装，车间内应根据实际需要设置合适的起吊设备。此外，桥架主体及桥架盖板结构层由外至内依次为保护层、防火层、防腐层、保护层，各层之间通过模压紧密结合成一体?。

5. Equipment settings? To adapt to the lifting of molds, suitable lifting equipment should be set up in the workshop according to actual needs. In addition, the main body of the bridge and the structural layer of the bridge cover plate are sequentially composed of a protective layer, a fireproof layer, an anti-corrosion layer, and a protective layer from the outside to the inside, and each layer is tightly integrated through molding?.

本文由济南电缆桥架友情奉献.更多有关的知识请点击:http://www.sddlqj.cn/真诚的态度.为您提供为多维度的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is a friendly contribution from Jinan Cable Bridge For more information, please click: http://www.sddlqj.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.